About Us
Products
Purchase
Downloads
Support
Forums
Contact Us
Site
 Register to post in forums, or Log in to your existing account
 

Play RetroMUD
Post new topic  Reply to topic     Home » Forums » zMUD General Discussion
Dragonar
Beginner


Joined: 14 Apr 2003
Posts: 16
Location: USA

PostPosted: Sat Feb 21, 2004 3:51 am   

Blank Line Problem
 
I get a blank line after each command I enter .. when it echos on the screen.. this didnt happen in my old Zmud and it is happening now.. is there anything I need to do to rectify this?

Thankyou for your answers.
Reply with quote
LightBulb
MASTER


Joined: 28 Nov 2000
Posts: 4817
Location: USA

PostPosted: Sat Feb 21, 2004 6:49 pm   
 
Your MUD is probably sending you the extra blank line. You may be able to eliminate it by changing config/set/auto/preferences on the MUD itself. You could also check your zMUD prefs, you might be able to eliminate it by disabling "Use GA/EOR for prompt" in the General/Emulation section.
Reply with quote
Dragonar
Beginner


Joined: 14 Apr 2003
Posts: 16
Location: USA

PostPosted: Sat Feb 21, 2004 7:14 pm   
 
As i recall my old Zmud didnt show this problem and I checked the configuration for the Mud itself and there is nothing i can do about it on it.. I tried disabling Echo in my Mud and well then since the command doesnt show the blank line doesnt as well and only the action shows but it's not preferrable for me.. Thankyou for your reply Light but can you or anyone else give me other suggestions?

Thankyou
Reply with quote
ElaineT
Newbie


Joined: 09 Feb 2004
Posts: 9
Location: USA

PostPosted: Mon Feb 23, 2004 7:59 am   
 
I am having the same problem, and it wasn't in the 6.x betas either, when connected to the same mud with the same configuation. I've looked all through the Zmud settings and can't figure out how to get rid of the blank lines.
Reply with quote
jmorzins
Newbie


Joined: 21 Feb 2004
Posts: 5
Location: USA

PostPosted: Mon Feb 23, 2004 8:17 pm   
 
quote:
Originally posted by Dragonar

I get a blank line after each command I enter ..



I am having the same blink line issue. It as if the process of sending a command to the mud displays an extra blank line after the sent command. I did not see this behavior in v6.62

However, it is difficult to track down exactly what is happening. I made a test connection to a simple echoserver that did no more than echo my text back at me, and saw no extra blank lines when communicating with the echo server.

So clearly this behavior depends on which mud you connect to. Given the fact that the behavior is new in 7.01, I hold out hope that it can be tracked down and the behavior removed in some future release.
Reply with quote
Dragonar
Beginner


Joined: 14 Apr 2003
Posts: 16
Location: USA

PostPosted: Tue Mar 02, 2004 10:26 am   
 
any new suggestions on this issue ?
Reply with quote
Pega
Magician


Joined: 08 Jan 2001
Posts: 341
Location: Singapore

PostPosted: Tue Mar 02, 2004 11:15 am   
 
I am on v7.03.

I see what you mean.
There is a difference between sending a command off the command-line,
and using #send {firstcommand%cr%{lf}secondcommand}.

It is there but I never noticed it, it never bothered me.
Was it not like that in v6.62?
Reply with quote
Display posts from previous:   
Post new topic   Reply to topic     Home » Forums » zMUD General Discussion All times are GMT
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum

© 2009 Zugg Software. Hosted by Wolfpaw.net